View clinical trials related to Mouth, Edentulous.
Filter by:the aim of this study is to compare the influence of different palatal vault configurations on the accuracy and scan speed of IO scans in cases of completely edentulous arches. The null hypothesis is that there is no difference in scanning time, and trueness and precision of IO scans between class I, II and III palatal vault configurations.
The goal of this cross-over clinical trial is to investigate the precision of digital implant impressions using an intraoral scanner and photogrammetry in obtaining complete-arch implant-supported scans. The main question[s] it aims to answer are: - Is there a difference in precision between intraoral scans and photogrammetry in obtaining digital implant scans? - Will arch perimeter and jaw type (maxilla vs. mandible) affect the precision results? Procedures: At each appointment, participants existing permanent/temporary prosthesis or healing caps were unscrewed and temporarily removed for the period of the consultation appointment. Scanbodies were screwed into their implants for the duration of the appointment. They underwent two types of digital implant impression procedures (five times each), including intraoral scan and photogrammetry. Intraoral and extraoral photography were taken. At the end of each appointment, the scanbodies were removed, and existing bridge/healing caps were reinserted. The procedures were not painful or required any form of local anesthetic Comparison group: Researchers compared the precision of intraoral scanning vs. photogrammetry to see which device provided the best precision outcomes.
The purpose of this study was to assess the effect of Bio-Hpp versus Co-Cr custom abutments in fixed-detachable implant-supported mandibular partial dentures clinically and radiographically in Class I Kennedy classification (split-mouth study)
The aim of this study was to describe a novel digital technique to analyze the wear of screw-retained implant-supported metal-ceramic dental prostheses and natural tooth as antagonist. Materials and methods: Ten patients were consecutively included to rehabilitate partial edentulism by dental implants. Both the screw-retained implant-supported metal-ceramic dental prostheses and the natural tooth as antagonist were submitted to a digital impression through an intraoral scan to generate a Standard Tessellation Language digital file preoperatively (STL1), at 3 months (STL2), and 6 months (STL3) follow-up. Afterwards, an alignment procedure of the digital files (STL1-STL3) was performed on a reverse engineering morphometric software and volume changes at the screw-retained implant-supported metal-ceramic dental prostheses and the natural tooth as antagonist were analyzed using Student's t-test. Moreover, Gage R&R statistical analysis was conducted to analyze the repeatability and reproducibility of the digital technique.
Analyzing and comparing the retention, accuracy, EMG and patient satisfaction of maxillary complete denture base fabricated by conventional and rapid prototyping techniques.
Objective of the present study was to assess the peri-implant soft tissue profiles between argon plasma pre-treated (PT) and non-treated (NPT) abutments by comparing clinical and histological parameters 2 months after abutment placement.
This study examines the effects of prosthetic treatment options applied to edentulous geriatric individuals who applied to Marmara University Faculty of Dentistry on chewing function, food consumption status, malnutrition status and oral health-related quality of life.
28 participants with edentulous maxillary arches were randomly selected and enrolled in two equal groups; Group I conventional impression group (CIG) and Group II Digital impression group (DIG). All patients were rehabilitated with maxillary screw-retained implant prosthesis retained by 6 implants. Prosthodontic complications and peri-implant MBL were registered at 6,12, and 24 months (m). Data was collected and statistically analyzed.
The aim of this study is to gather clinical data related to the use of Plastalgin and Plastalgin Fast, in order to comply with the new medical device regulation. The target population for this study is the same as the intended population specified in the study device's instructions for use: children from 5 years old and adults. Collection, recording, and reporting of data will be accurate and will ensure the privacy, health, and welfare of participating patients during and after the study
Introduction: One major complaint frequently voiced by complete denture wearers is denture retention. Conventional denture disadvantage is heat-curing resin deformation. In addition, the pack and press technique that is still more common, residual stresses that occur at the time of packing are released when the material is removed from the flask, causing the resin to shrink, and this shrinkage is cited as a cause of poor fit of the denture base, In the field of prosthetic dentistry, the ability of additive manufacturing to fabricate prosthetic devices based on CAD data influences the overall quality, the mechanical properties of printed parts, the total cost and the manufacturing time. The milling process wastes large quantities of denture base material, and more recent three-dimensional (3D) prototyping promises a more sustainable additive approach by using less denture resin. However, no clinical reports have been published regarding the accuracy of the mucosal surface or denture retention for denture fabricated using conventional techniques compared to those fabricated using additive manufacturing. Aim of the study: Investigate the effect of two techniques of complete denture manufacturing (conventional and 3D printed) on denture retention, trueness (accuracy), and satisfaction. Methodology: Twenty patients will be selected from the outpatient clinic and will be divided into 2 groups, group A for conventional dentures and group B for 3D printed dentures, retention for the two groups will be measured at 0,1 and 3 months, and patient satisfaction will be recorded, and accuracy of the denture base will be measured on the software. The results will be tabulated and statistically analyzed using the SPSS program.