Microarchitecture of the Augmented Bone Following Sinus Elevation — MAB  

Alveolar Bone Loss Clinical Trial

Official title: Biomaterials in the Surgical Rehabilitation of Oral and Maxillofacial Hard and Soft Tissue Defects

Status Completed

Clinical Trial Summary

In this prospective randomized clinical study sinus floor elevation procedures are preformed using different biomaterials with the lateral window technique. After a 6-month healing, at the time of dental implant placement bone core biopsy samples are harvested. The samples undergo micro-Ct and histomorphometric analysis.

Clinical Trial Description

Aim of the study The aim of this prospective randomized study is to evaluate the remodeling capacity of albumin impregnated freeze-dried bone allograft in sinus floor augmentation by histomorphometry and micro-CT analysis and to compare it to anorganic bovine xenograft material. Surgical methods Patients performed oral rinse with 0.2% chlorhexidine solution for 1 min before surgery. Under local anesthesia a full thickness flap was raised from a midcrestal incision along with two relieving incisions. Lateral window osteotomies were carried out with diamond burs. The Schneiderian membrane was carefully elevated. Bone graft material was packed in the defect with light force. Patients were randomly assigned to 2 groups based on the type of bone filler: albumin impregnated allograft (BoneAlbumin, OrthoSera GmbH, Krems an der Donau, Austria) or anorganic bovine bone mineral (ABBM), (Bio-Oss Geistlich Wolhusen, Switzerland). A porcine collagen membrane (Bio Gide, Geistlich GmbH, Wolhusen, Switzerland) was placed over the lateral window and fixed by titanium pins (Titan Pin Set, Ustomed Instruments Ulrich Storz GmbH & Co. KG, Tuttlingen, Germany). The buccal flap was mobilized to allow tension-free primary closure. The margins were stabilized with single interrupted sutures. Antibiotics (1 g amoxicillin-clavulanate twice a day for 5 days, or in case of side effects or known allergy to penicillin, 300 mg clindamycin 4 times a day for 4 days), anti-inflammatory drugs (50 mg diclofenac 3 times a day for 3 days), and chlorhexidine mouthwash (twice a day for 21 days from the first day after surgery) were prescribed. Sutures were removed after 10 days. After 6 months healing surgical re-entry procedure took place under local anesthesia. A bone core biopsy was taken with a trephine with an external diameter of 3.5 mm and an internal diameter of 2.5 mm (330 205 486 001 025 Hager & Meisinger GmbH, Neuss, Germany) and implants of at least 4.0 mm of diameter were placed into the grafted alveolus nonsubmerged. Histomorphometry Bone core biopsy material was fixed in 10% buffered formaldehyde solution. Following decalcination and dehydration, the biopsy material was embedded in paraffin and 20 µm sections were prepared. The sections were stained with routine haematoxylin eosin stain. Sections were evaluated under a light microscope in magnification 40×-400× . Histomorphometric measurements were completed on sections with Panoramic Viewer 1.15 (3DHISTECH Ltd., Budapest, Hungary) using a combination of Adobe PhotoShop (Adobe System Inc., San Jose, CA, USA) and ImageJ, the public domain NIH Image program (US National Institutes of Health' http://rsb.info.nih.gov/nih-image/) at 150× magnification. Two slides of the augmented areas in each bone core biopsy sample were evaluated to record area percentage of newly formed bone, residual particles of the bone graft material, and the bone marrow space according to published protocols. Histomorphometric data consisted of the area percentage of newly formed bone, residual particles of the graft material and bone marrow were identified in each section. Micro-CT analysis The bone core biopsy samples were scanned using a microcomputed tomography (μCT) scanner (Skyscan 1172 X-ray microtomograph, Bruker µCT, Kontich, Belgium). After the acquisition, raw images were reconstructed using NRecon software (v.1.7.1.6., Bruker µCT, Kontich, Belgium). The morphometric variables relevant to our study calculated by CTAn software (v.1.17.7.2, Bruker µCT, Kontich, Belgium). On the reconstructed images of each sample the demarcation plane of the host and the augmented area was identified and the complete available tissue (maxilla or augmented bone, respectively) were selected as regions of interest (ROIs) for quantitative analysis. Micromorphometric data was collected by evaluation of the augmented bone of the test or control group. Additional micromorphometric data was recorded by analyzing the native bone of the alveolar ridge within the bone core biopsy samples of both test and control group. The microarchitectural parameters of the augmented bone of the BoneAlbumin group and the ABBM group; the augmented bone of the BoneAlbumin group and the native bone of the alveolar ridge; the augmented bone of the ABBM group and the native bone of the alveolar ridge were compared. Statistical analysis Percentage values of each bone core biopsy sample were used to calculate descriptive statistics for the histomorphometrical and quantitative µCT analysis. The results were analyzed statistically using the IBM SPSS Statistics 23 data analysis software program (IBM Corporation, New York, NY. USA). The Kruskal Wallis One-way ANOVA test was used to compare two sets of data for the statistical analysis of the histomorphometric results. One-way ANOVA test was used to compare three sets of data for the statistical analysis of the micromorphometric results of the micro-CT. Values of p < 0.05 were considered statistically significant. CBCT CBCT imaging (PaX-Reve3D, Vatech, Hwaseong, South-Korea) was carried out prior to sinus floor elevation to evaluate the anatomy and possible pathology of the maxillary sinuses, then 6 months after bone augmentation prior to implant placement (preoperative CBCT), and 3 years after implant placement (postoperative CBCT). To register the preoperative and postoperative CBCT data by anatomical landmarks 3DSlicer 4.10.2 software (The Brigham and Women's Hospital, Inc. Boston, USA) was used. The ROIs were identified by determining the central axis of the implants and placing a virtual cylinder on the preoperative CBCT image sequence with a diameter of 2,5 mm and the length of 8 mm on this axis corresponding with the inner dimensions of the trephine used for bone core biopsy harvesting. The image sequences of selected ROIs were imported in CTAn software (v.1.17.7.2, Bruker micro-CT, Kontich, Belgium) and micromorphometric variables were calculated by the software. Statistical analysis of CBCT results Correlation of the micromorphometric data obtained from the CBCT images and micro-CT images was determined by The Spearman's rank-order correlation. Statistical analysis was performed using the IBM SPSS Statistics 25 data analysis software program (IBM Corporation, New York, USA). Values of P < 0.05 were considered statistically significant. ;

Related Conditions & MeSH terms

• Alveolar Bone Loss
• Edentulous; Alveolar Process, Atrophy
• Sinus Pneumatization

• NCT number: NCT04136509
• Study type: Interventional
• Source: Semmelweis University
• Status: Completed
• Phase: N/A
• Start date: January 1, 2016
• Completion date: September 1, 2021