View clinical trials related to Malocclusion, Angle Class III.
Filter by:to compare Palatal and buccal protraction using plates assisted with facemask in growing class III patients
The purpose of this study is to assess and compare the effect of two appliances (Hybrid-Hyrax expander/ Bonded rapid maxillary expander (RME)) supported by different anchorage units and two different expansion procedures (routine rapid maxillary expansion protocol (routine)/ alternative rapid expansion and constriction protocol (alt-RAMEC)) on maxillary protraction during face mask (FM) treatment.
Diverse viewpoints exist regarding the correlation between the conventional rapid maxillary expansion (RME) and facemask approach and the alternative RME and facemask hybrid technique (Alt-RAMEC) in terms of the degree of maxillary protraction. The findings of the study may offer a novel approach to protocol selection based on the anomaly's degree of severity. The objective of this investigation is to assess and contrast the skeletal and dentoalveolar outcomes of three distinct Alt-RAMEC techniques.
Bilateral sagittal split osteotomy (BSSO) is considered the main osteotomy design in corrective mandibular surgery, however abnormal anatomical configuration of the posterior mandible with rolled out inferior border and thin mandibular rami with cortically adherent inferior alveolar nerve may interfere with the utilization of this osteotomy. The aim of this study is to introduce a novel modification of the intraoral inverted L ramus osteotomy (ILRO) to overcome these limitations in mandibular setback surgery. preoperative CBCT was requested for virtual planning and fabrication of cutting and drilling guides. Cutting lines were outlined to be consisted of four cuts; lateral ostectomy to uncover and lateralize the inferior alveolar nerve (IAN), posterior cut run horizontally from the anterior border of the ramus to a point just above the mandibular foramen, two anterior vertical cuts run from the anterior end of the lateral ostectomy to the inferior mandibular border. The guide was removed and the osteotomy lines were completed then the mandibular setback was oriented and fixed using pre-bent plates osteosynthesis. Inferior alveolar nerve function was regained perfectly one year post-operatively. This procedure introduces a robust alternative to the BSSO osteotomy in some cases of mandibular setback surgery.
This in vivo comparative study will evaluate the changes in the mandibular dimensions and the glenoid fossa after skeletal class III subjects' therapy by chincup appliance and compare it with an untreated class III control group. Pre and post-treatment low-dose computed tomography images will be taken before and after achieving positive overjet and undergoing 16 months of active treatment/ observation. Dimensional and volumetric changes in the mandible, condyles, and glenoid fossa will be calculated and compared to those observed in the control group.
Stability of the orthodontic miniscrews placed in the mandible is still considered to bare higher risk of failure compared to other intraoral locations. The aim of our study was to determine the influence of the miniscrew size on their long-term stability, occurrence of oral mucosa inflammation and pain lasting over 48 hours after implantation.
The aim of this prospective study is to analyze the postoperative paresthesias experienced in patients who undergo bilateral sagittal split osteotomies (BSSO) using an ultrasonic saw, versus a reciprocating saw. Patients included in the study are ages 15-45 scheduled to undergo BSSO surgery at the University of California, San Francisco. One side of the patient's mandible will be instrumented with either the Stryker Sonopet ultrasonic saw or traditional reciprocating saw, while the other side will receive the remaining intervention (determined via randomization on the day of surgery). Patient paresthesias will then be analyzed on each side for 3 months postoperatively (at postoperative days: 1, 7, 14, 28, and 84). Sensory examinations will be carried out by blinded examiners using von Frey hairs and two point discrimination testing. Patients will also subjectively rate their sensation on each side. The results will then be analyzed to determine if patient paresthesias, including the severity and duration, differed depending on which instrument was used, the ultrasonic or reciprocating saw.
The aim of this study was to evaluate the changes in head posture, position of the hyoid bone, pharyngeal airway and cervical posture after the use of Petit type face mask in patients with skeletal class III malocclusion (ANB angle < 0) with ongoing growth. No other study was found in the literature in which head posture, cervical posture, and hyoid bone position were evaluated after the use of a face mask and compared with a control group consisting of patients of the same age group and the same malocclusion.
Various malocclusions require the extraction of the first premolars and retraction of the canines with the need for maximum anchorage. If the canines are pulled into the extraction space using the molar teeth for support, unwanted tooth movement occurs. This study aims to evaluate the effect of temporary anchorage devices and power arms, which are auxiliary orthodontic appliances in reducing undesirable tooth movements.
Early orthodontic treatment of Class III malocclusions with skeletal and dentoalveolar imbalances, represents a continuous dilemma. This difficulty starts from their meticulous diagnosis and treatment planning till reaching satisfactory results and finally stability. Some appliances could be used to correct growing skeletal Class III patients, improving the skeletal and dentoalveolar relationships, creating proper conditions for final orthodontic treatment, more importantly avoiding surgery. These appliances remove patient compliance from the equation.