Healing of Post-ext Sites Using Bovine Bone Mineral: a CBCT and Histologic RCCT

Edentulous Alveolar Ridge Clinical Trial

Official title: Healing of Post-extraction Sites Using Bovine-bone Mineral: a CBCT and Histologic Randomized Controlled Clinical Study

Status Completed

Clinical Trial Summary

Aim of the present investigation will be to evaluate the role of a bovine-bone mineral and a collagen membrane as ridge augmentation procedure following tooth extraction. 20 consecutive adult patients, requiring tooth extraction in the frontal area of the upper and lower arch maxilla (from second premolar to second premolar), will be enrolled into the study.

After tooth extraction, sockets will be randomized and divided into two groups: in Group A the socket will be grafted with Bio-Oss Collagen , in Group B the sockets will be grafted with BioOss granules (small granules). The graft will be covered with porcine collagen membrane (BioGide). Then, the flap will be sutured.

MEASUREMENTS:

The end of the study will be fixed at the 6 months evaluation after tooth extraction. Impression will be taken before tooth extraction and after 6 months in order to create cast models. On the cast models, using reference PVC (polyvinylchloride) guides, the horizontal dimension of the soft tissues will be measured. One measurement per tooth will be recorded, at T0 (before extraction) and T2 (after 6 months).

A 3D radiological image, using the CBCT technique, will be obtained at the end of the surgical stage T1 (extraction + bone graft) and after 6 months of healing. Superimposition will be performed in order to measure hard tissue remodelling.

After six months (T6), a a biopsy specimen will be also harvested for that augmented extractions sockets on which an implant installation has been previously planned.

Clinical Trial Description

Both animal and human studies have clearly demonstrated that the healing of post extraction sites usually results in pronounced alveolar ridge resorption, that mostly stabilized after 4 to 6 months. The marked tri-dimensional alterations of the ridge volume may jeopardize patients' aesthetics and create anatomical difficulties for further implant placement.

Aim of the present investigation will be to evaluate the role of a bovine-bone mineral and a collagen membrane as ridge augmentation procedure (intended as "increase of the ridge volume beyond the skeletal envelope existing at the time of extraction") following tooth extraction. Furthermore, the authors aim to evaluate as the collagen membrane acts when used for "open-healing".

20 consecutive adult patients, requiring tooth extraction in the frontal area of the upper and lower arch maxilla (from second premolar to second premolar), will be enrolled into the study.

After local anesthesia, a buccal full thickness flap will be elevated, and then the hopeless teeth will be gently extracted. All granulation tissue will be removed from the alveolus, that will be rinsed with saline. At this time the post-extraction sockets will be randomized and divided into two groups: in Group A the socket will be grafted with Bio-Oss Collagen , in Group B the sockets will be grafted with BioOss granules (small granules) using the Bio-Oss Pen device.

The graft will be covered with porcine collagen membrane (BioGide). Then, the flap will be sutured. The sutures (single sutures) will involve only the interdental gingival tissue, and no attempt will be done to reach a complete soft tissue closure of the sockets: in the alveolus area BioGide will be mostly left exposed, intended as "open healing" for second intention wound healing.

The patient swill assume antibiotics per 6 days (Amoxicillin + Clavulanate 1gr), and will rinse with Digluconate Chlorhexidine 0.20% per 14 days. At day 14 the sutures will be removed. If, at this moment, the gingiva over the graft will not be completely closed, the patient will use Digluconate Chlorhexidine 0.20% until the secondary closure will be completed.

MEASUREMENTS:

The end of the study will be fixed at the 6 months evaluation after tooth extraction (corresponding to the planned time for implant installation).

Impression will be taken before tooth extraction and after 6 months in order to create cast models. On the cast models, using reference PVC guides, the horizontal dimension of the soft tissues (measured perpendicular to the tangent of the dental arch at the midpoint of the extraction site as the distance between the most prominent points buccally and orally) will be measured. One measurement per tooth will be recorded, at T0 (before extraction) and T2 (after 6 months).

A 3D radiological image, using the CBCT technique, will be obtained at the end of the surgical stage T1 (extraction + bone graft) and after 6 months of healing. Using a diagnostic software, superimposition will be performed in order to measure hard tissue remodelling.

After six months (T6), a a biopsy specimen will be also harvested for that augmented extractions sockets on which an implant installation has been previously planned, with the purpose of an histologic and histomorphometric evaluation (measurement of new bone formation and measurement of remaining BioOss granules). The biopsy will be taken exactly in the area where dental implants will be placed. ;

Study Design

Allocation: Randomized, Endpoint Classification: Safety/Efficacy Study, Intervention Model: Parallel Assignment, Masking: Single Blind (Outcomes Assessor), Primary Purpose: Treatment

Related Conditions & MeSH terms

• Edentulous Alveolar Ridge
• Loss of Teeth Due to Extraction
• Tooth Loss

• NCT number: NCT01800149
• Study type: Interventional
• Source: Proed
• Status: Completed
• Phase: Phase 4
• Start date: February 2013
• Completion date: December 2014