View clinical trials related to Malocclusion, Angle Class III.
Filter by:The aim of the study is to compare a customized facemask for the treatment of Class III malocclusion in the prepubertal growing patient (patients between the ages of 5 and 12 years) versus a standard commercial facemask. Specifically, preference, pain, difficulty in sleeping, time of use, and possible complications for the two types of facemasks will be analyzed. This is a single-center, national, controlled, superiority, randomized, crossover, open-label study. Each patient will be treated with both the customized facemask and the standard commercial facemask. Each patient will wear one type of facemask for 2 months and the other type of facemask for the next 2 months. After 2 weeks and at the end of therapy with each of the facemask types, the patient, with the possible help of the parents, will have to answer a questionnaire about pain and difficulty sleeping and report any complications. In addition, after completing both phases (fourth month), the patient should indicate a preference for one of the two types of mask with which to complete therapy for an additional 6 months.
A randomized clinical trial to introduce a modified 3D printed customized maxillary protraction facemask and evaluate its efficacy in comparison with the conventional maxillary protraction facemask therapy in correction of Class III malocclusion of young patients
The purpose of this study is to assess and compare the effect of two appliances (Hybrid-Hyrax expander/ Bonded rapid maxillary expander (RME)) supported by different anchorage units and two different expansion procedures (routine rapid maxillary expansion protocol (routine)/ alternative rapid expansion and constriction protocol (alt-RAMEC)) on maxillary protraction during face mask (FM) treatment.
Diverse viewpoints exist regarding the correlation between the conventional rapid maxillary expansion (RME) and facemask approach and the alternative RME and facemask hybrid technique (Alt-RAMEC) in terms of the degree of maxillary protraction. The findings of the study may offer a novel approach to protocol selection based on the anomaly's degree of severity. The objective of this investigation is to assess and contrast the skeletal and dentoalveolar outcomes of three distinct Alt-RAMEC techniques.
The purpose of this prospective study is to compare treatment outcomes and the quality of life of skeletal Class III patients treated with conventional fixed appliances and aligners undergoing Surgery-first approach. Data will be collected through validated questionnaires: OQLQ (Orthognathic Quality of Life Questionnaire), OHIP-14 (Oral Health Impact Proļ¬le), SF-36 (Medical Outcomes Study 36 - Item Short-Form Health Survey) and IOTN (Index of Orthodontic Treatment Need).
This study hypotheses that using low medial cut osteotomy BSSO in mandibular setback can be an efficient and effective method to limit the bony segment interferences , decreasing muscles stripping during osteotomy ,decrease condylar torque and so securing preoperative condylar position during BSSO in comparison with using high medial cut BSSO.
the PowerScope appliance is found to be efficient for the treatment of class II malocclusion. Accordingly, it appears valuable to investigate the efficiency of skeletally anchored powerScope in the treatment of class III malocclusion
Bilateral sagittal split osteotomy (BSSO) is considered the main osteotomy design in corrective mandibular surgery, however abnormal anatomical configuration of the posterior mandible with rolled out inferior border and thin mandibular rami with cortically adherent inferior alveolar nerve may interfere with the utilization of this osteotomy. The aim of this study is to introduce a novel modification of the intraoral inverted L ramus osteotomy (ILRO) to overcome these limitations in mandibular setback surgery. preoperative CBCT was requested for virtual planning and fabrication of cutting and drilling guides. Cutting lines were outlined to be consisted of four cuts; lateral ostectomy to uncover and lateralize the inferior alveolar nerve (IAN), posterior cut run horizontally from the anterior border of the ramus to a point just above the mandibular foramen, two anterior vertical cuts run from the anterior end of the lateral ostectomy to the inferior mandibular border. The guide was removed and the osteotomy lines were completed then the mandibular setback was oriented and fixed using pre-bent plates osteosynthesis. Inferior alveolar nerve function was regained perfectly one year post-operatively. This procedure introduces a robust alternative to the BSSO osteotomy in some cases of mandibular setback surgery.
This in vivo comparative study will evaluate the changes in the mandibular dimensions and the glenoid fossa after skeletal class III subjects' therapy by chincup appliance and compare it with an untreated class III control group. Pre and post-treatment low-dose computed tomography images will be taken before and after achieving positive overjet and undergoing 16 months of active treatment/ observation. Dimensional and volumetric changes in the mandible, condyles, and glenoid fossa will be calculated and compared to those observed in the control group.
Stability of the orthodontic miniscrews placed in the mandible is still considered to bare higher risk of failure compared to other intraoral locations. The aim of our study was to determine the influence of the miniscrew size on their long-term stability, occurrence of oral mucosa inflammation and pain lasting over 48 hours after implantation.