BONDING TO ENAMEL USING A UNIVERSAL ADHESIVE

Clinical Trial Clinical Trial

— RCT  

Official title:

STRATEGIES FOR BONDING TO ENAMEL USING A UNIVERSAL ADHESIVE ON SELF-ETCHING MODE

Clinical Trial Details — Status: Completed

Administrative data

• NCT number: NCT03254693
• Other study ID #: 56013116.0.0000.0107
• Status: Completed
• Phase: Phase 4
• First received: August 15, 2017
• Last updated: August 27, 2017
• Start date: February 1, 2016
• Est. completion date: August 1, 2017

Study information

• Verified date: August 2017
• Source: Universidade Estadual de Ponta Grossa
• Contact: n/a
• Is FDA regulated: No
• Study type: Interventional

Clinical Trial Summary

Objective: This double-blind randomized clinical trial evaluates strategies for improving the bonding of universal adhesive to enamel in non-carious cervical lesions (NCCL) of a new universal multi-mode adhesive (Ambar Universal; FGM).

Methods: A total of 134 restorations were randomly placed in 19 patients according to the following groups: SE - Self-etch; SEE - Selective etching; SE2X - Self-etch doble time; SE1+

• Self-etch additional layer. The resin composite Opallis (FGM) was placed incrementally. The restorations were evaluated after one week (baseline), 6 and 12 months, using the FDI and USPHS criteria. Statistical analyses were performed using appropriate tests (=0.05).

Description:

Interventions: restorative procedure All the patients selected for this study received dental prophylaxis with a suspension of pumice and water in a rubber cup and signed an informed consent form two weeks before the restorative procedures.

The degree of sclerotic dentin from the NCCLs was measured according to the criteria described by Swift and others. The cavity dimensions in millimeters (height, width, and depth), the geometry of the cavity (evaluated by profile photograph and labeled at <45o, 45o-90o, 90o<135o, and >135o), the presence of an antagonist, and the presence of attrition facets were observed and recorded. Pre-operative sensitivity was also evaluated by applying air for 10 s from a dental syringe placed 2 cm from the tooth surface and with an explorer. These features were recorded to allow comparison of the baseline features of the dentin cavities among experimental groups.

To calibrate the restorative procedure, the study director placed one restoration of each group to identify all steps involved in the application technique. Then, the two operators, who were resident dentists with more than five years of clinical experience in operative dentistry, placed four restorations, one of each group, under the supervision of the study director in a clinical setting. The restoration failures were shown to the operators prior to starting the study. At this point, the operators were considered calibrated to perform the restorative procedures.

The operators restored all teeth. All participants received four restorations, one of each experimental group in different lesions previously selected according to the inclusion criteria.

Before restorative procedures, the operators anesthetized the teeth with a 3% mepivacaine solution (Mepisv, Nova DFL, Rio de Janeiro, RJ, Brazil) and cleaned all lesions with pumice and water in a rubber cup, followed by rinsing and drying. Then, shade selection was made using a shade guide.

Cleaning of all lesions with pumice and water in a rubber cup was carried out, followed by rinsing and drying. Using a shade-selection guide, the proper shade of the composite was determined. Following the ADA guidelines, the operators did not prepare any additional retention or bevel.

The NCCLs received the multimode adhesive system applied in different modes: 1-step self-etch approach (SE), selective enamel etching (SEE), 1-step self-etch applied for double time in the enamel (SE2X), 1-step self-etch approach with additional layer (SE1+) was applied as described below. The compositions, more details regarding the adhesion strategies used and batch numbers are described in Table 2.

The adhesives were light-cured with a LED light-curing unit (1,000 mW/cm2) (Radii-cal), according to the manufacturer's instructions (Table 2). Opallis (FGM) composite resin was used in 2 to 3 increments, each one being light-cured (Radii-cal) for 30 s. The restorations were finished immediately with fine #2200 diamond burs (KG Sorensen). Polishing was performed with rubber points (Astropol, Ivoclar Vivadent, Liechtenstein).

Recruitment information / eligibility

• Status: Completed
• Enrollment: 35
• Est. completion date: August 1, 2017
• Est. primary completion date: August 1, 2017
• Accepts healthy volunteers: Accepts Healthy Volunteers
• Gender: All
• Age group: 18 Years and older

Eligibility

Inclusion Criteria:

• Participants had to be in good general health.

• At least 18 years old

• Have an acceptable oral hygiene level

• Present at least 20 teeth under occlusion

• At least four NCCLs in four different teeth

• These lesions had to be non-carious, non-retentive, deeper than 1 mm, and involve both the enamel and dentin of vital teeth without mobility.

• The cavo-surface margin could not involve more than 50% of enamel, and all lesions had cervical margins ending in dentin.

Exclusion Criteria:

• Participants had not be in good general health.

• At less 18 years old

• Have not an acceptable oral hygiene level

• Present at less 20 teeth under occlusion

• At less four NCCLs in four different teeth, these lesions had not be non-carious, retentive and involve only enamel of vital teeth with mobility.

Related Conditions & MeSH terms

• Clinical Trial

Intervention

Combination Product:
• 1-step self-etch approach (SE)
Application mode - Do not use etchan. According to the manufacturer's instructions.
• selective enamel etching (SEE)
Application mode - Etch only on enamel for 15 s. Rinse for 15s. Air dry to remove excess water.According to the manufacturer's instructions.

Other:
• 1-step self-etch for double time (SE2X)
Application mode - Do not use etchan. According to the manufacturer's instructions, but for the double time (20 s) in the each application.
• 1-step self-etch additional layer (SE1+)
Application mode - Do not use etchan. According to the manufacturer's instructions, but apply tree times.

Locations

Country	Name	City	State
Brazil	Universidade Estadual do Oeste do Paraná	Cascavel	Paraná

Sponsors (2)

Lead Sponsor	Collaborator
Universidade Estadual de Ponta Grossa	Coordenação de Aperfeiçoamento de Pessoal de Nível Superior.

Country where clinical trial is conducted

Brazil, 

Outcome

Type	Measure	Description	Time frame	Safety issue
Primary	Retention	The primary clinical endpoint was restoration retention/fracture.	6 montths
Secondary	Marginal Adaptation	Restoration marginal adaptation.	6 months